The ATX 4-pin power supply connector is a standard motherboard power connector used to provide +12 VDC to the processor voltage regulator.

What is a 4 pin power connector?

The P4 connector is a 12V power supply cable used with motherboards that have an Intel Pentium 4 or later processor. Today, the connector is a standard power connector and is used with both Intel and AMD motherboards. All of these wires attach to a four pin connection on the motherboard.

Where does the connector power supply 4 pin processor go?

Our power supply units (PSUs) use an 8-pin EPS12v CPU cable that can be split into two 4-pin connectors. If you want to connect our PSU into a 4-pin EPS motherboard port, simply pull the two halves of the connector apart and connect one half into the motherboard port.

Is the 4 pin power connector needed?

This connector is used to supply additional 12V current to the motherboard. While the system will likely still run without it, higher current demands such as extreme overclocking or large video card current draws may require it.

What is a 4 pin connector called?

The Molex 4-pin power supply connector is one of the standard peripheral power connectors in computers today. The power connector itself is a Molex 8981 connector called the AMP MATE-N-LOK.

Can you plug an 8 pin into a 4 pin?

As with plugging a 24 pin cable into a 20 pin motherboard connector, you can plug an 8 pin cable into a 4 pin connector and leave 4 pins hanging over the end but you can also have the same problems with things preventing it from fitting. It will work fine if it fits.

Can you use a 4 pin in a 8 pin?

The 8-pin connector is literally designed as two of the 4-pin connectors put together. It is entirely possible to just plug the 4-pin connector in the 8-pin slot. It wont damage anything, but the motherboard will detect the difference and either not start up at all, or run in a VERY restricted mode.

Can you put a 8 pin into a 4 pin?

Yes, it will work. Ive used an 8pin on a 4 pin motherboard and its still running. The extra pins are for more power for higher overclocking, 4 is enough to power your system.

Do I need both the 8 pin and 4 pin CPU power plug?

You dont actually NEED both connectors plugged in. Usually the motherboard functions perfectly with just the 8-pin connected. Youd have to have a very high end CPU or a very overclocked CPU in order to actually NEED both connections populated.

Do I need both 8 pin and 4 pin?

It is not necessary to use the additional 4 pin connector if youre not pushing the board or CPU too hard. You have to plug in the 8pin connector. If youre going to overclock the cpu plug in both. If youre not just the 8pin connection.

What is the function of 4 pin Berg connector?

the four-pin polarized Berg connectors used to connect 3½-inch floppy disk drive units to the power supply unit, usually referred to as simply a floppy power connector, but often also referred to as LP4. This connector has a 2.50 mm (0.098 in) pitch (not 2.54 mm).

What is the purpose of 4 pin Molex connector?

The Molex connector is used for power connections for a disk drive in a computer as well as for other computer components such as CD-ROMs, graphic cards etc. The Molex connectors bring DC power to the drives inside a PC case.

Can I put a 4 pin connector?

The answer is yes. A 4-pin can be put, by itself, into an 8-pin CPU power socket and the machine boot up and run. It will give it what power it can, and if the CPU draws more than that, it will shut the system down. If it shuts down when you start doing intensive stuff, just underclock the CPU.

Do I need both 8 pin CPU connectors?

You have to plug in the 8pin connector. If youre going to overclock the cpu plug in both. If youre not just the 8pin connection.

Is 8 pin enough for 5600X?

The 8 pin is more than enough for running the system. Youre totally fine without it. If youre upgrading to a RTX 3070 or 3080 and a Ryzen 5600X your 650 Watts should be enough since its a good model. Total draw at full load will be like ~ 500 watts for the system with a 3080 and 5600X.

Are all 8 pin connectors the same?

They are completely different. The EPS connector is meant to supply power to a motherboard cpu socket while the PCI express connector is meant to supply power to a GPU.

What voltage does a floppy drive use?

All 3.5 floppy drives use +5V solely, the 12V on standard power connector simply not used.

Where does the floppy connector go?

Today, if any floppy drive is in the computer it would connects to Drive A: and the end cable connected to the motherboard. The floppy channel, FDD header, or floppy connection is where the floppy drive connects to the computer motherboard.

What is the function of 4 pin Molex P4 12V?

This Motherboard P4 12V 4-Pin to Molex 4-Pin Power Adapter Cable is used when you want to upgrade your system to a Pentium 4 (P4) system. Using this cable allows you to upgrade without having to buy a new power supply.

Can 3 pin fans plug into 4 pin?

1 Answer. Apparently a 3-pin fan can plug directly into a 4-pin socket. Two of the pins provide power to the fan, the 3rd provides an RPM pulse to the motherboard to read the speed. The 4th pin is for PWM speed control.