How do you finish drywall around a tub surround?

0:0210:16How to finish Drywall around tub or shower surround - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then run it over the top and run it up against the top not a bad option the other option ofMoreAnd then run it over the top and run it up against the top not a bad option the other option of course is to just mud it and then run mesh tape over the top mud it again with a skim coat and sand it.

Do you caulk between shower and drywall?

Shower stalls usually have a flange that gets nailed to the studs, and its outer edge gets covered when you install drywall. This leaves a gap between the edge of the drywall and the stall that you have to fill with silicone caulk, using a caulking gun.

How do you fill a gap between shower tray and wall?

6 Answers from MyBuilder Bathroom Fitters Ideally the tiling would come down over the edge of the shower tray but if your walls are really out of square,you can get sealing strips to go around the join between wall and tray.

How do you seal a tub surround?

1:213:12How to Seal Around A Tub Or Shower - YouTubeYouTubeStart of suggested clipEnd of suggested clipCut the tip off the cartridge at a 45 degree angle to your desired bead size we recommend 3/8 of anMoreCut the tip off the cartridge at a 45 degree angle to your desired bead size we recommend 3/8 of an inch. Using a caulking gun applying sealant with steady pressure forcing the sealant into the joint.

What kind of drywall goes under a tub surround?

Install cement board or an equivalent moisture-resistant backing material on walls behind tub and shower enclosures composed of tile or panel assemblies with caulked joints. Dont use paper-faced backer board, i.e., paper-faced drywall, behind seamed tub and shower enclosures.

What should I put above my shower surround?

What to Do With the Wall Above the Shower Surround?Tile It Up. Add a few rows of decorative tile above the surround to extend it all the way to the ceiling. Waterproof Art. Touch of Paint. Simple Shelves. Raise a Panel.

Do you have to put drywall behind shower surround?

Fiberglass and acrylic tub and shower enclosures come with a flanged edge that attaches directly to the wall studs, and the proper way to hide this flange is to install drywall over it. Consequently, enclosures are typically installed on the bare studs.

What is the gap between tiles and shower trays?

Re: Gap between wall tiles and shower tray I tend to leave a 2mm gap between tray and tiles.

How do you seal between shower trays and tiles?

1:254:23How to Seal a Shower Tray or Tub with Silicone - Tile MountainYouTube

Do you put drywall behind a tub surround?

Fiberglass and acrylic tub and shower enclosures come with a flanged edge that attaches directly to the wall studs, and the proper way to hide this flange is to install drywall over it. Consequently, enclosures are typically installed on the bare studs.

Should there be drywall behind a tub surround?

The short answer to the question is, “Its not recommended.” However, this answer only really only suffices if youre converting a room that was never a bathroom into a wet space. Drywall on its own is not suitable for use in bathrooms because it is prone to absorbing moisture and thus losing structural integrity.

Can you tile above a shower insert?

Just as you can use tile inside the shower itself, you can finish the wall above it with ceramic tile. Using subway tile above shower inserts adds a different look than traditional tile because of its smaller size. Once this dries, you can use a notched trowel and mastic adhesive to mount the tiles.

Can you put tile above a tub surround?

Tiling around a bathtub introduces additional challenges. If the tub is level, set a full tile at its top edge. For a tub surround only, install the backerboard and tile 12 inches above the tub. When tiling around a tub, mark the first layout line at the vertical edge of the tile next to the tub.

Do you put insulation behind shower walls?

The insulation behind the tub or shower should be equivalent to the insulation in the rest of the exterior walls and should be covered with an air barrier of cement backer board, rigid foam insulation, or non-paper-faced drywall that is sealed at the edges and seams to provide a continuous air seal.

How do you caulk a surround?

0:325:03How to Caulk Bathtub Surround Tiles, Perfectly Straight Lines DIYYouTube

What is the gap between tiles?

Common practice is 2-3mm for wall tiles and 3-5mm for floor tiles. The key difference in tile type, in relation to grout lines, is whether you tile is rectified or not. A rectified tile is one which is cut or manufactured to a precise measured size.